Analysis Settings Input Reference

 

DATA ITEMS

 

COMSPC             (in Settings:Analysis Settings:Section Properties Options)

 

ECC-i                  (in Settings:Analysis Settings:Section Properties Options)

 

ECFACT                (only available by direct editing)

 

FBSPC                (in line girder projects with Settings:Analysis Settings:Live Load + Impact Options)

 

IMP-i                  (in girder system projects with Settings:Analysis Settings:Live Load + Impact Options)

 

IMPACT              (in line girder projects with Settings:Analysis Settings:Live Load + Impact Options)

 

IMPACTP            (only available by direct editing)

 

IXB-i                  (in Settings:Analysis Settings:Section Properties Options)

 

IXBR                  (in Settings:Analysis Settings:Section Properties Options)

 

IXC-i                  (in Settings:Analysis Settings:Section Properties Options)

 

IXG-i                  (in Settings:Analysis Settings:Section Properties Options)

 

IXL-i                   (in Settings:Analysis Settings:Section Properties Options)

 

JB-i                     (in Settings:Analysis Settings:Section Properties Options)

 

JBR                     (in Settings:Analysis Settings:Section Properties Options)

 

JG-i                     (in Settings:Analysis Settings:Section Properties Options)

 

NMOD                 (in Settings:Analysis Settings:Section Properties Options)

 

MLFACTORS        (only available by direct editing)

 

PRECST               (only available by direct editing)

 

PSLABW              (in Settings:Analysis Settings:Slab Pouring Settings)

 

SEQUENCE          (in Settings:Analysis Settings:Slab Pouring Settings)

 

SLBOVRLAY        (only available by direct editing)

 

SLBSPC               (in Settings:Analysis Settings:Slab Pouring Settings)

 

STAGFCT             (only available by direct editing)

 

WETGROUPS       (in Settings:Analysis Settings:Slab Pouring Settings)

 

WIND                  (only available by direct editing)

 

WINDT                (only available by direct editing)

 

WINDTSTEEL      (only available by direct editing)

 

 

CONDITION ITEMS

 

APPLY IMPACT AT AXLE LOCATION

    (in Settings:Analysis Settings:Live Load + Impact Options)

 

APPLY IMPACT AT FORCE LOCATION

    (in Settings:Analysis Settings:Live Load + Impact Options)

 

ASSUME SLAB ON FLANGE FOR SECTION PROPERTIES 

    (in Settings:Analysis Settings:Section Properties Options)

 

AVERAGE LIVE DEFLECTIONS

    (only available by direct editing)

 

AVERAGE SIDEWALK LIVE LOAD DEFLECTIONS

    (only available by direct editing)

 

AVERAGE SPANS FOR REACTION IMPACT

    (in Settings:Analysis Settings:Live Load + Impact Options)

 

BRACING NOT BOLTED AT ABUTMENTS FOR NONCOMPOSITE DEAD ANALYSIS

    (in Settings:Analysis Settings:Modeling Settings)

 

COMBINED STANDARD AND PERMIT EFFECTS

    (only available by direct editing)

 

COMPOSITE ACTION FROM FRICTION

    (only available by direct editing)

 

COMPOSITE AT PIER FOR STIFFNESS ANALYSIS ONLY

    (only available by direct editing)

 

CONSTANT MODULAR RATIO

    (only available by direct editing)

 

FOM MOMENT SMOOTHING

    (in Settings:Analysis Settings:Stress Check Settings)

 

FULL COMPOSITE ACTION DURING POUR SEQUENCE

    (in Settings:Analysis Settings:Slab Pouring Settings)

 

GRID MODEL

    (in Settings:Analysis Settings:Modeling Settings)

 

HIGH RESOLUTION MESH    

    (in Settings:Analysis Settings:Modeling Settings)

 

HINGES FOR STEEL SELF WEIGHT ONLY

    (in Settings:Analysis Settings:Modeling Settings)

 

HINGES FOR TOTAL SELF WEIGHT ONLY

    (in Settings:Analysis Settings:Modeling Settings)

 

IGNORE IMPACT

    (in Settings:Analysis Settings:Live Load + Impact Options)

 

IGNORE LIVE LOADING

    (in Settings:Analysis Settings:Live Load + Impact Options)

 

IGNORE MOMENT SHIFTING

    (in Settings:Analysis Settings:Stress Check Settings)

 

IGNORE NEGATIVE MOMENT SLAB FOR PERMANENT DEFORMATION

    (only available by direct editing)

 

IGNORE SIDEWALK FOR LIVE DEFLECTIONS

    (only available by direct editing)

 

IGNORE TRUCK TRAIN FOR REACTION

    (only available by direct editing)

 

IGNORE WET CONCRETE STRESS CHECK

    (in Settings:Analysis Settings:Stress Check Settings)

 

INCLUDE LONGITUDINAL WEB STFNER IN SECTION PROPS

    (in Settings:Analysis Settings:Section Properties Options)

 

INCLUDE NEGATIVE MOMENT REBAR FOR STIFFNESS ANALYSIS

    (only available by direct editing)

 

INCLUDE PEDESTRIAN LOADING FOR MULTIPLE LANE FACTOR

    (only available by direct editing)

 

INCLUDE SLAB FILLER IN SECTION PROPERTIES

    (in Settings:Analysis Settings:Section Properties Options)

 

INTEGRAL SUPPORTS FOR COMPOSITE ANALYSIS ONLY

    (only available by direct editing)

 

INTEGRAL SUPPORTS EXCEPT FOR STEEL ANALYSIS

    (only available by direct editing)

 

INCLUDE TANDEM TRUCK FOR MAX NEG MOMENT

    (only available by direct editing)

 

INTERMEDIATE BRACING NOT BOLTED FOR COMPOSITE ANALYSIS

    (in Settings:Analysis Settings:Modeling Settings)

 

INTERMEDIATE BRACING NOT BOLTED FOR NONCOMPOSITE DEAD ANALYSIS

    (in Settings:Analysis Settings:Modeling Settings)

 

INTERMEDIATE BRACING NOT BOLTED FOR STEEL ANALYSIS

    (in Settings:Analysis Settings:Modeling Settings)

 

LOCAL WHEEL DISTRIBUTION ONLY

    (only available by direct editing)

 

LONG TERM MODULUS USED IN POURING

    (only available by direct editing)

 

LOW RESOLUTION MESH             

    (in system projects with Settings:Analysis Settings:Modeling Settings)

 

MEDIUM RESOLUTION MESH

    (in system projects with Settings:Analysis Settings:Modeling Settings)

 

NEG MOM SLAB NOT USED IN COMPOSITE ANALYSIS

    (in Settings:Analysis Settings:Section Properties Options)

 

NEG MOM SLAB NOT USED IN DEAD LOAD 2 ANALYSIS

    (in Settings:Analysis Settings:Section Properties Options)

 

NO COMPOSITE ACTION DURING POUR SEQUENCE

    (in Settings:Analysis Settings:Slab Pouring Settings)

 

NONCOMPOSITE GIRDER

    (in Settings:Analysis Settings:Section Properties Options)

 

NONCOMPOSITE SLAB IS NOT CONTINUOUS BRACING

    (only available by direct editing)

 

PARTIAL COMPOSITE ACTION DURING POUR SEQUENCE

    (in Settings:Analysis Settings:Slab Pouring Settings)

 

PLATE AND ECCENTRIC BEAM FINITE ELEMENT MODEL

    (in Settings:Analysis Settings:Modeling Settings)

 

PRECST PANELS ENTIRE LENGTH ON FIRST POUR

    (only available by direct editing)

 

REMOVE FORMS AFTER EACH POUR

    (only available by direct editing)

 

WIND BRACING ALL BAYS

    (in Settings:Analysis Settings:Stress Check Settings)

 

WIND BRACING EVERY OTHER BAY

    (in Settings:Analysis Settings:Stress Check Settings)

 

 

Related topics:

Overview of Analysis Settings in Girder System Projects

Overview of Analysis Settings in Line Girder Projects